I am not a chemist but for a university project i am dealing with simulations concerning a potentiostat using a 3-electrode setup.

For example in the book Electrochemical Methods (Bard & Faulkner, Second edition 2001) on page 642 they give this example of a (adder) potentiostat which inputs three different potentials $e_1, e_2$ and $e_3$:

enter image description here

While the working electrode is grounded, point $S$ is on virtual ground and by using Kirchhoff's rule they obtain

$$-i_{ref} = i_1 + i_2 + i_3.$$

By using Ohm's law they rewrite this equation into

$$-e_{ref} = e_1 \cdot \frac{R_{ref}}{R_1} + e_2 \cdot \frac{R_{ref}}{R_2} + e_3 \cdot \frac{R_{ref}}{R_3},$$

with $e_{ref}$ being the potential of the working electrode with respect to the reference electrode.

With all resistors having the same value this can be expressed as

$$-e_{ref} = e_1 + e_2 + e_3$$

They state:

Thus the circuit maintains the working electrode at a potential equal to the weighted sum of the inputs

As far as I understand, the electrode of interest is the working electrode which potential should be varied (with the reference electrode providing a stable reference potential) to study its properties. But from the description above the potential of the working electrode does not change and instead the potential at the reference electrode changes.


1 Answer 1


Bard and Faulkner are outstanding electrochemists, but that potentiostat figure always annoys me because it makes it seem as though current flows through the reference electrode and that the working electrode is literally grounded. In reality, the reference electrode should conduct extremely low currents (pA, really) and the current through the working electrode is what you care about, as a function of the electroactive species in th potentiostat's solution.

Therefore, consider Fig. 15.24 and surrounding text from from Horowitz and Hill 1:

Horowitz & Hill Fig. 15.24

In this three wire potentiostat, the bottom operational amplifier (op amp) simply works as a transimpedance amplifier, converting current at the working electrode to voltage. In this regard, it is basically a very low input impedance ammeter, which approximates an ideal ammeter. So the working electrode is held at virtual ground, which typically means less than a millivolt from true ground.

The potential at the inverting input of the upper op amp must equal the input reference voltage, $\mathrm V_{ref}$, to within less than a millivolt. Note that $\mathrm V_{ref}$ can be from a ramp generator, a function generator or from another op amp, as in the inverting summing op amp in the figure from Bard and Faulkner. Importantly, note that virually no current flows through the reference electrode, because of the extremely high input impedance of the op amp inputs, so it will function properly and not become polarized or damaged.

The potential between the working and reference electrodes is $\mathrm V_{ref}$ because the working electrode is clamped to virtual ground and the potential of the reference electrode is clamped at $\mathrm V_{ref}$. The solution in the cell has an impedance, which is generally complex, and the solution spans the volume between the counter electrode (also called the auxilliary electrode) and the working electrode. The reference electrode is physically placed as close to the working electrode as is feasible.

Now let $\mathrm Z_{c}$ denote the solution impedance between the counter and reference electrodes and let $\mathrm Z_{u}$ denote the solution impedance between the reference and working electrodes. Then we have a non-inverting voltage follower with gain, as shown is this figure:

Non-inverting op amp

The output voltage, $\mathrm V_{o}$, is the voltage at the counter electrode. Therefore, $$\mathrm V_{o} = [(Z_{c} + Z_{u})/Z_{u}] \times V_{ref} \tag{1}$$

But the voltage at the junction of $\mathrm Z_{c}$ and $\mathrm Z_{u}$ , i.e., in the solution where the reference electrode is located, is $\mathrm V_{ref}$. Therefore $$\mathrm V_{ref} = [Z_{u}/(Z_{c} + Z_{u})] \times V_{o} \tag{2}$$

If solution impedances change, the upper op amp will source or sink current, as necessary, by changing $\mathrm V_{o}$, thereby maintaining the solution potential, at the reference electrode, equal to $\mathrm V_{ref}$.

1 P. Horowitz, W. Hill, The Art of Electronics, 2nd Ed., Cambridge University Press, Cambridge, ©1989, pp. 1015-1016.

  • $\begingroup$ Bard and Faulkner show a similar extension to the the circuit as the one you presented. Since the working electrode is grounded doesn't the statement "Thus the circuit maintains the working electrode at a potential equal to the weighted sum of the inputs" is wrong, when in fact the reference electrode is subject to change. Do I understand it correctly, that when we ignore $Z_c$ and $Z_u$ (e.g. by changing $V_{ref}$ rapidly), the working electrode is always at ground potential and the potential of the reference electrode is subject to change? $\endgroup$
    – Waffelei
    Mar 4, 2020 at 3:30
  • $\begingroup$ The figure in your question is messed up in several ways: the reference current is negligible and would go the other way anyway. To measure the current would require, say, a known resistor between the op amp output and the counter electrode. So I see no point in beating that dead horse. In the H & H circuit, the upper op amp provides whatever current is necessary to keep the solution at the input reference potential. No actual reference electrode, e.g., Ag|AgCl, is shown, but if that were inserted in the obvious way, then the op amp would compensate as expected. So the circuit maintains the $\endgroup$
    – Ed V
    Mar 4, 2020 at 3:43
  • $\begingroup$ solution in the vicinity of the working electrode at the user-specified potential. $\endgroup$
    – Ed V
    Mar 4, 2020 at 3:45
  • $\begingroup$ A colleague of my reports the page reference in The Art of Electronics is typo'd: he reckons it should be pp. 1015-1016. $\endgroup$ Apr 1, 2020 at 8:12
  • $\begingroup$ Thanks for pointing out my error: your colleague is right! I just corrected the mistake. I intend to buy the 3rd edition, released a whopping 29 years after the second edition. $\endgroup$
    – Ed V
    Apr 1, 2020 at 12:29

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.