The seasoning on cast iron is formed by fat polymerization, fat polymerization is maximized with a drying oil, and flaxseed oil is the only drying oil that’s edible.
...
Fat polymerization can be triggered or accelerated in a variety of ways. As best I can tell from my reading, the cast iron seasoning process is an example of “radical polymerization”. The process is initiated when something causes the release of free radicals in the oil. The free radicals then “crosslink” to form the tough, hard film you see in a well-seasoned pan.
So what is the “something” that initiates the release of free radicals in fat? Iron, for one thing. High heat, light, and oxygen, for some others. To prevent cooking oils from going rancid – i.e., breaking down and releasing free radicals – you need to store them in dark, tightly sealed containers in a cool location. To initiate or accelerate the release of free radicals, put the oil in contact with bare iron and heat it above its smoke point, which will cause even non-drying oils to release free radicals
...
Buy an organic flaxseed oil. You don’t want to burn toxic chemicals into your cookware to leach out forever more. It’s a fairly expensive oil. I paid $17 for a 17 ounce bottle of cold-pressed, unrefined, organic flaxseed oil. As it says on the bottle, shake it before you use it.
Strip your pan down to the iron using the techniques I describe in my popover post. Heat the pan in a 200°F oven to be sure it’s bone dry and to open the pores of the iron a little. Then put it on a paper towel, pour a little flaxseed oil on it (don’t forget to shake the bottle), and rub the oil all over the pan with your hands, making sure to get into every nook and cranny. Your hands and the pan will be nice and oily.
Now rub it all off. Yup – all. All. Rub it off with paper towels or a cotton cloth until it looks like there is nothing left on the surface. There actually is oil left on the surface, it’s just very thin. The pan should look dry, not glistening with oil. Put the pan upside down in a cold oven. Most instructions say to put aluminum foil under it to catch any drips, but if your oil coating is as thin as it should be, there won’t be any drips.
Turn the oven to a baking temperature of 500°F (or as high as your oven goes – mine only goes to 450°F) and let the pan preheat with the oven. When it reaches temperature, set the timer for an hour. After an hour, turn off the oven but do not open the oven door. Let it cool off with the pan inside for two hours, at which point it’s cool enough to handle.
The pan will come out of the oven a little darker, but matte in texture – not the semi-gloss you’re aiming for. It needs more coats. In fact, it needs at least six coats. So again rub on the oil, wipe it off, put it in the cold oven, let it preheat, bake for an hour, and let it cool in the oven for two hours. The picture above was taken after six coats of seasoning. At that point it starts to develop a bit of a sheen and the pan is ready for use.
If you try this, you will be tempted to use a thicker coat of oil to speed up the process. Don’t do it. It just gets you an uneven surface – or worse, baked on drips. Been there, done that. You can’t speed up the process. If you try, you’ll mess up the pan and have to start over.
The reason for the very hot oven is to be sure the temperature is above the oil’s smoke point, and to maximally accelerate the release of free radicals. Unrefined flaxseed oil actually has the lowest smoke point of any oil (see this table). But the higher the temperature the more it will smoke, and that’s good for seasoning (though bad for eating – do not let oils smoke during cooking).
I mentioned earlier there’s a myth floating around that vegetable oils leave a sticky residue. If the pan comes out of the oven sticky, the cause is one of three things:
- You put the oil on too thick.
- Your oven temperature was too low.
- Your baking time was too short.
There is also a comment section below the article.
